bikesetting

Rocky Mountain Altitude Powerplay: suspension setup & specs

Manufacturer data retrieved on 26 September 2026 · 3 builds · Bike type: Full-suspension e-MTB

The Rocky Mountain Altitude Powerplay is an e-enduro bike with 170 mm of fork travel and 160 mm at the rear. It is powered by Rocky Mountain Dyname 4.0. Here you will find all 3 current builds with fork, shock and shock size, plus matching SAG and tyre pressure starting values.

Calculate the setup for your Rocky Mountain Altitude Powerplay →

All builds

Fork, shock, shock size (eye-to-eye length × stroke) and rear travel, motor, weight and price according to the manufacturer. Wheel size: 29.

BuildForkShockShock sizeRear travelMotorWeightRRPCalculator
Alloy 30RockShox Domain Gold RC (170 mm)Marzocchi Bomber Air–160 mmRocky Mountain Dyname 4.0
720 Wh
––Setup →
Alloy 50RockShox Zeb Select RC (170 mm)FOX Float X Performance–160 mmRocky Mountain Dyname 4.0
720 Wh
––Setup →
Carbon 70FOX 38 Float EVOL GRIP X2 Factory Series (170 mm)FOX Float X2 Factory–160 mmRocky Mountain Dyname 4.0
720 Wh
––Setup →

How it compares

On travel, the Rocky Mountain Altitude Powerplay is right where the “e-enduro bike” category usually is: 170 mm up front against a median of 170 mm from 56 bikes. The rear offers 160 mm, 10 mm less than the front. The frame is made of carbon.

For suspension, Rocky Mountain combines components from FOX, Marzocchi and RockShox. In total, 3 different forks are used, from the RockShox Domain Gold RC to the FOX 38 Float EVOL GRIP X2 Factory Series. It is powered by Rocky Mountain Dyname 4.0 with a 720 Wh battery.

Setup notes for this spec

Target SAG for the Rocky Mountain Altitude Powerplay

The table converts the recommended SAG percentages into millimetres, so you can check them with the O-ring directly on the stanchion and on the shock shaft. Adjust the air pressure until the value is right. If Rocky Mountain specifies its own target SAG for your model, that takes priority.

170 mm fork (all builds)

Riding styleFork SAG
XC / touring17 % = 29 mm
Trail20 % = 34 mm
Enduro / rough22 % = 37 mm
Bike park20 % = 34 mm

How to measure SAG is explained in our guide SAG setup.

Tyre pressure starting values

The values apply to 2.50″ wide tubeless tyres with a trail casing, including the e-MTB surcharge. With an inner tube add about 0.2 bar (2.9 psi), with an insert take off about 0.1 bar (1.5 psi). Stock tyres: F: Maxxis Assegai 2.5 WT 3C MaxxGrip DD Tubeless Ready | R: Maxxis Minion DHR II 2.4 WT 3C MaxxTerra DD Tubeless Ready; F: Maxxis Minion Assegai 2.5 WT EXO Tubeless Ready | R: Maxxis Minion DHR II 2.4 WT EXO Tubeless Ready | Tubeless Set Up | Sealant Incl.

Ready-to-ride weightFrontRear
60 kg1.48 bar (21 psi)1.68 bar (24 psi)
70 kg1.60 bar (23 psi)1.80 bar (26 psi)
80 kg1.72 bar (25 psi)1.92 bar (28 psi)
90 kg1.84 bar (27 psi)2.04 bar (30 psi)
100 kg1.96 bar (28 psi)2.16 bar (31 psi)
110 kg2.08 bar (30 psi)2.28 bar (33 psi)
120 kg2.20 bar (32 psi)2.40 bar (35 psi)

Air pressure in the fork and shock

You will find a guide value for air pressure on the fork sticker (or on the shock) or in the suspension makers’ charts. Our calculator also takes riding style and rebound into account. In the end, measured SAG is what counts.

Note: all values without guarantee. Specification can vary by model year, frame size and market – if in doubt, the type plate, the manual and Rocky Mountain’s information apply. Never exceed maximum pressures.

Sources

More Rocky Mountain bikes