Orbea Wild LT: suspension setup & specs
The Orbea Wild LT is an e-enduro bike with – mm of fork travel and 170 mm at the rear. It is powered by DJI Avinox M2 or DJI Avinox M2S. Here you will find all 7 current builds with fork, shock and shock size, plus matching SAG and tyre pressure starting values.
Calculate the setup for your Orbea Wild LT →
All builds
Fork, shock, shock size (eye-to-eye length × stroke) and rear travel, motor, weight and price according to the manufacturer. Wheel size: 29.
| Build | Fork | Shock | Shock size | Rear travel | Motor | Weight | RRP | Calculator |
|---|---|---|---|---|---|---|---|---|
| H20 | RockShox ZEB | FOX Float X Performance | – | 170 mm | DJI Avinox M2 800 Wh | – | €5,599 | Setup → |
| H10 | FOX 38 Performance | FOX Float X Performance | – | 170 mm | DJI Avinox M2S 800 Wh | – | €6,999 | Setup → |
| M20 | RockShox ZEB | FOX Float X Performance | – | 170 mm | DJI Avinox M2S 800 Wh | – | €6,999 | Setup → |
| H-TEAM | FOX 38 Factory Kashima | FOX Float X2 Factory Kashima | – | 170 mm | DJI Avinox M2S 800 Wh | – | €7,999 | Setup → |
| M10 | FOX 38 Factory Kashima | FOX Float X2 Factory Kashima | – | 170 mm | DJI Avinox M2S 800 Wh | – | €8,499 | Setup → |
| M-TEAM RS | FOX 38 Factory Kashima | FOX Float X2 Factory Kashima | – | 170 mm | DJI Avinox M2S 800 Wh | – | €9,999 | Setup → |
| M-LTD RS | FOX 38 Factory Kashima | FOX Float X2 Factory Kashima | – | 170 mm | DJI Avinox M2S 800 Wh | – | €13,499 | Setup → |
How it compares
Prices for the Orbea Wild LT start at €5,599 (H20), below the category median of €6,900. The top build, M-LTD RS, costs €13,499. For suspension, Orbea combines components from FOX and RockShox. In total, 3 different forks are used, from the RockShox ZEB to the FOX 38 Factory Kashima. Drive comes from DJI Avinox M2 or DJI Avinox M2S, paired with 800 Wh of battery capacity.
Setup notes for this spec
- Fork (RockShox ZEB): air goes in through the valve on top of the left leg. After every change, compress the fork firmly a few times before measuring SAG.
- Rebound: on FOX and RockShox suspension the rebound adjuster is red. Always count clicks from fully closed (clockwise to the stop) so you can return to any setting.
- Air shock (FOX Float X Performance): measure SAG in your riding position, ideally with a helper holding the bike. Cycle the shock a few times after every pressure change.
- e-MTB: because of the extra weight, start with slightly more tyre pressure – the surcharge is already built into the table below.
Target SAG for the Orbea Wild LT
The table converts the recommended SAG percentages into millimetres, so you can check them with the O-ring directly on the stanchion and on the shock shaft. Adjust the air pressure until the value is right. If Orbea specifies its own target SAG for your model, that takes priority.
How to measure SAG is explained in our guide SAG setup.
Tyre pressure starting values
Basis: 2.60″ tyre width, tubeless, trail casing, including the e-MTB surcharge. If you run tubes, add about 0.2 bar (2.9 psi); with an insert, about 0.1 bar (1.5 psi) less is enough.
| Ready-to-ride weight | Front | Rear |
|---|---|---|
| 60 kg | 1.40 bar (20 psi) | 1.60 bar (23 psi) |
| 70 kg | 1.52 bar (22 psi) | 1.72 bar (25 psi) |
| 80 kg | 1.64 bar (24 psi) | 1.84 bar (27 psi) |
| 90 kg | 1.76 bar (26 psi) | 1.96 bar (28 psi) |
| 100 kg | 1.88 bar (27 psi) | 2.08 bar (30 psi) |
| 110 kg | 2.00 bar (29 psi) | 2.20 bar (32 psi) |
| 120 kg | 2.12 bar (31 psi) | 2.32 bar (34 psi) |
Air pressure in the fork and shock
You will find a suitable starting pressure on the sticker on the fork stanchion (or on the shock) or in the suspension manufacturers’ setup charts. Our calculator gives you a starting value including rebound for your weight and riding style. What matters afterwards is the measured SAG from the table above.